Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1309.3097 · Journal of the Optical Society of America B

Noise reduction and hyperfine level coherence in spontaneous noise spectroscopy of atomic vapor

Takahisa Mitsui, Kenichiro Aoki

Published Jan 2, 2014• 8 citations
arXivHTMLPDF

Abstract

We developed a system for measurements of power spectra of transmitted light intensity fluctuations, in which the extraneous noise, including shot noise, is reduced. In essence, we just apply light, measure the power of the transmitted light, and derive its power spectrum. We use this to observe the spontaneous noise spectra of photon atom interactions. Applying light with frequency modulation, we can also observe the spontaneous noise reflecting the coherence between the hyperfine levels in the excited state. There are two main novel components in the measurement system, the noise reduction scheme and the stabilization of the laser system. The noise reduction mechanism can be used to reduce the shot noise contribution to arbitrarily low levels through averaging, in principle. This is combined with differential detection to keep unwanted noise at low levels. The laser system is stabilized to obtain spectral width below 1 kHz without high frequency (≳10 MHz) noise. These methods are described systematically and the performance of the measurement system is examined through experimental results.

DOI
10.1364/josab.31.000195

Related papers

Noise Spectroscopy of K Atoms with a Diode Laser

Taro Ito, Noboru Shimomura, T. Yabuzaki

There has been much interest in the influence of the laser noise on the atomic system. So far theoretical works have been performed on calculation of the mean values and the variance of the fluctuated atomic populations, and verified through observation of the fluctuating resonance fluorescence from the atomic vapors. Yabuzaki et al. have observed the excess intensity noise of the resonant light from a diode laser propagated through alkali atomic vapor. They have measured the intensity power spectrum of the light when the laser was tuned near the D2 line of Cs and observed all corresponding hyperfine-splitting resonances in the excited state and Zeeman splitting resonances within a hyperfine level of the ground state. Walser et al. have theoretically studied the intensity fluctuation of laser light propagated through a weakly absorbing medium. The calculated power spectrum of a phase-diffusing field has been found qualitative agreement with the experimental results by Yabuzaki et al. on hyperfine-splitting resonances. Recently, Mitsui has reported a new type of noise spectroscopy with a highly stabilized diode laser. He has investigated the spontaneous noise appeared in optical detection of magnetic resonance of Rb atoms. In this note we report the first observation of hyperfine spectra in the ground state of K and K appearing as the intensity fluctuation at hyperfine splittings of 462MHz and 254MHz of circularly polarized light from a diode laser transmitted through a sample cell. We have also observed the Zeeman hyperfine spectra of K in a static magnetic field. We show that the spectra are strongly dependent of the direction of the static magnetic field. Their splittings as functions of the strength of static magnetic field are compared with the Breit–Rabi formula. The experimental apparatus is quite simple as shown in Fig. 1. The diode laser used was an ordinary Fabry–Perot type with output power of 5mW, operating near the D1 line (769.9 nm) of K atoms. The output of the laser was circularly polarized and applied to a cell containing K vapor at a temperature 90 C, corresponding atomic density to be about 1:15 10 cm 3. The transmitted light was detected by an avalanche photo-diode having frequency response up to 1GHz. The output of the photo-diode was applied to a rf frequency analyzer to obtain the power spectrum of the fluctuation of the transmitted light intensity. A static magnetic field is provided by two pairs of Helmholtz coils mutually perpendicular and about 90 cm in diameter. The strength of the magnetic field is calibrated by using magnetic resonance signals of optically pumped Rb atoms. Figure 2 shows the frequency spectrum of the intensity fluctuation of transmitted light observed when the laser was tuned to the transition from the state F 1⁄4 1 in the ground state to the state F0 1⁄4 1 in the excited state by adjusting the driving current of the laser diode. Sharp resonance signals can be seen at the hyperfine splittings of K and K, 462 and 254MHz, respectively, on the background of broad noise spectrum. When a weak static magnetic field H0 is applied to the K vapor, the hyperfine spectra of K splits into several lines (the effective gyro-magnetic ratio of K is known to be 1⁄4 2 700 kHz/G). Figures 3(a) and 3(b) show the observed Zeeman hyperfine spectra of K for

Journal of the Physical Society of Japan•Apr 15, 2003•4 citations

Spontaneous Noise Spectroscopy of an Atomic Magnetic Resonance

Takahisa Mitsui

We have experimentally demonstrated a new type of noise spectroscopy, which requires neither amplitude nor frequency noise of the light source. A highly stabilized diode laser provides low-noise light for the optical magnetic resonance of Rb atoms. The laser light transmitted through the Rb vapor contains significant intensity fluctuations whose power spectrum has a distinct peak at the Larmor frequency. The fluctuations are spontaneously generated by the atoms and are attributed to the stochastic properties of the photon scattering which randomly interrupts the Larmor precession of the atomic magnetic moment.

Physical Review Letters•Jun 5, 2000•49 citations

Noise Correlation Spectroscopy: A Review

Gombojav O. Ariunbold

The frequency noise of an ordinary diode laser, often a nuisance in spectroscopy, can be used to measure atomic coherence. When atoms are prepared in a coherent superposition of two ground states, each random shift in laser frequency changes how much light they absorb, so the transmitted light carries a record of that coherence. Correlating the intensity fluctuations of two fields, each linking one ground state to a shared excited state, reads this record out, a technique known as noise correlation spectroscopy. The correlation signal is narrower than the transparency window the same fields create and switches sign as their frequency difference is tuned. Its width is set by the rate at which the atoms lose coherence and, over a wide range, does not grow with laser power. Over two decades the method has spread from warm vapors to cold atoms, to multi-field schemes, and to diamond and rare-earth-doped crystals. This review, to the author's knowledge the first, brings together its theory, experiments and applications, and examines its limits, the challenges that remain, and the opportunities that could make it a standard spectroscopic tool.

arXiv:2610.22392•Oct 12, 2026•0 citations

Observing random walks of atoms in buffer gas through resonant light absorption

Kenichiro Aoki, Takahisa Mitsui

Using resonant light absorption, random-walk motions of rubidium atoms in nitrogen buffer gas are observed directly. The transmitted light intensity through atomic vapor is measured, and its spectrum is obtained, down to orders of magnitude below the shot-noise level to detect fluctuations caused by atomic motions. To understand the measured spectra, the spectrum for atoms performing random walks in a Gaussian light beam is computed, and its analytical form is obtained. The spectrum has $1/{f}^{2}$ ($f$ is frequency) behavior at higher frequencies, crossing over to a different, but well-defined, behavior at lower frequencies. The properties of this theoretical spectrum agree excellently with the measured spectrum. This understanding also enables us to obtain the diffusion constant, the photon cross section of atoms in buffer gas, and the atomic number density from a single spectral measurement. We further discuss other possible applications of our experimental method and analysis.

arXiv:1605.07739•Physical Review A•Jul 18, 2016•14 citations

Photon noise reduction in lasers

Fritz Haake, S. M. Tan, Daniel F. Walls

We consider the problem of reducing the contributions of pump and spontaneous-emission noise to the output noise of a laser field. We consider two models based on an atomic medium, one analytic, the other involving numerical simulation of a sequence of pump cycles. The predictions of both models are shown to agree. For regular pump excitation the intensity fluctuations of a laser well above threshold may be reduced to zero at the cavity resonance frequency if the ratio of the lifetimes of the upper and lower lasing levels is sufficiently large that spontaneous emission is suppressed. When the atomic lifetimes are comparable, spontaneous emission reduces the amount of noise reduction. For example, for equal atomic lifetimes regular pump excitation will result in a maximum noise reduction in the output field of one-half the shot-noise limit.

Physical Review A•Dec 1, 1989•95 citations

Michelson interferometry with quantum noise reduction

Takahisa Mitsui, Aoki, Kenichiro

A Michelson interferometer with noise reduction to sub-shot noise levels is proposed and realized. Multiple measurements of a single signal beam are taken and the quantum property of light plays an essential role in the principle underlying this interferometry. The method makes use of the coherent state of light and requires only a simple modification to the standard Michelson interferometer. The surface fluctuation spectra of liquids are measured using this method down to a few orders of magnitude below the shot noise level. The spectrum derived from hydrodynamical considerations agrees well with the observed results for water. However, for oil, slight deviations are seen at high frequencies ($\gtrsim1\,$MHz), perhaps indicating its more complex underlying physics. The measurement requires a relatively low light power and a short time, so that it has a wide range of applicability.

arXiv:1206.3828•Jun 18, 2012•2 citations
We developed a system for measurements of power spectra of transmitted light intensity fluctuations, in which the extraneous noise, including shot noise, is reduced. In essence, we just apply light, measure the power of the transmitted light, and derive its power spectrum. We use this to observe the spontaneous noise spectra of photon atom interactions. Applying light with frequency modulation, we can also observe the spontaneous noise reflecting the coherence between the hyperfine levels in the excited state. There are two main novel components in the measurement system, the noise reduction scheme and the stabilization of the laser system. The noise reduction mechanism can be used to reduce the shot noise contribution to arbitrarily low levels through averaging, in principle. This is combined with differential detection to keep unwanted noise at low levels. The laser system is stabilized to obtain spectral width below 1 kHz without high frequency (≳10 MHz) noise. These methods are described systematically and the performance of the measurement system is examined through experimental results.
There has been much interest in the influence of the laser noise on the atomic system. So far theoretical works have been performed on calculation of the mean values and the variance of the fluctuated atomic populations, and verified through observation of the fluctuating resonance fluorescence from the atomic vapors. Yabuzaki et al. have observed the excess intensity noise of the resonant light from a diode laser propagated through alkali atomic vapor. They have measured the intensity power spectrum of the light when the laser was tuned near the D2 line of Cs and observed all corresponding hyperfine-splitting resonances in the excited state and Zeeman splitting resonances within a hyperfine level of the ground state. Walser et al. have theoretically studied the intensity fluctuation of laser light propagated through a weakly absorbing medium. The calculated power spectrum of a phase-diffusing field has been found qualitative agreement with the experimental results by Yabuzaki et al. on hyperfine-splitting resonances. Recently, Mitsui has reported a new type of noise spectroscopy with a highly stabilized diode laser. He has investigated the spontaneous noise appeared in optical detection of magnetic resonance of Rb atoms. In this note we report the first observation of hyperfine spectra in the ground state of K and K appearing as the intensity fluctuation at hyperfine splittings of 462MHz and 254MHz of circularly polarized light from a diode laser transmitted through a sample cell. We have also observed the Zeeman hyperfine spectra of K in a static magnetic field. We show that the spectra are strongly dependent of the direction of the static magnetic field. Their splittings as functions of the strength of static magnetic field are compared with the Breit–Rabi formula. The experimental apparatus is quite simple as shown in Fig. 1. The diode laser used was an ordinary Fabry–Perot type with output power of 5mW, operating near the D1 line (769.9 nm) of K atoms. The output of the laser was circularly polarized and applied to a cell containing K vapor at a temperature 90 C, corresponding atomic density to be about 1:15 10 cm 3. The transmitted light was detected by an avalanche photo-diode having frequency response up to 1GHz. The output of the photo-diode was applied to a rf frequency analyzer to obtain the power spectrum of the fluctuation of the transmitted light intensity. A static magnetic field is provided by two pairs of Helmholtz coils mutually perpendicular and about 90 cm in diameter. The strength of the magnetic field is calibrated by using magnetic resonance signals of optically pumped Rb atoms. Figure 2 shows the frequency spectrum of the intensity fluctuation of transmitted light observed when the laser was tuned to the transition from the state F 1⁄4 1 in the ground state to the state F0 1⁄4 1 in the excited state by adjusting the driving current of the laser diode. Sharp resonance signals can be seen at the hyperfine splittings of K and K, 462 and 254MHz, respectively, on the background of broad noise spectrum. When a weak static magnetic field H0 is applied to the K vapor, the hyperfine spectra of K splits into several lines (the effective gyro-magnetic ratio of K is known to be 1⁄4 2 700 kHz/G). Figures 3(a) and 3(b) show the observed Zeeman hyperfine spectra of K for
We have experimentally demonstrated a new type of noise spectroscopy, which requires neither amplitude nor frequency noise of the light source. A highly stabilized diode laser provides low-noise light for the optical magnetic resonance of Rb atoms. The laser light transmitted through the Rb vapor contains significant intensity fluctuations whose power spectrum has a distinct peak at the Larmor frequency. The fluctuations are spontaneously generated by the atoms and are attributed to the stochastic properties of the photon scattering which randomly interrupts the Larmor precession of the atomic magnetic moment.
The frequency noise of an ordinary diode laser, often a nuisance in spectroscopy, can be used to measure atomic coherence. When atoms are prepared in a coherent superposition of two ground states, each random shift in laser frequency changes how much light they absorb, so the transmitted light carries a record of that coherence. Correlating the intensity fluctuations of two fields, each linking one ground state to a shared excited state, reads this record out, a technique known as noise correlation spectroscopy. The correlation signal is narrower than the transparency window the same fields create and switches sign as their frequency difference is tuned. Its width is set by the rate at which the atoms lose coherence and, over a wide range, does not grow with laser power. Over two decades the method has spread from warm vapors to cold atoms, to multi-field schemes, and to diamond and rare-earth-doped crystals. This review, to the author's knowledge the first, brings together its theory, experiments and applications, and examines its limits, the challenges that remain, and the opportunities that could make it a standard spectroscopic tool.
Using resonant light absorption, random-walk motions of rubidium atoms in nitrogen buffer gas are observed directly. The transmitted light intensity through atomic vapor is measured, and its spectrum is obtained, down to orders of magnitude below the shot-noise level to detect fluctuations caused by atomic motions. To understand the measured spectra, the spectrum for atoms performing random walks in a Gaussian light beam is computed, and its analytical form is obtained. The spectrum has 1/f21/{f}^{2}1/f2 (fff is frequency) behavior at higher frequencies, crossing over to a different, but well-defined, behavior at lower frequencies. The properties of this theoretical spectrum agree excellently with the measured spectrum. This understanding also enables us to obtain the diffusion constant, the photon cross section of atoms in buffer gas, and the atomic number density from a single spectral measurement. We further discuss other possible applications of our experimental method and analysis.
We consider the problem of reducing the contributions of pump and spontaneous-emission noise to the output noise of a laser field. We consider two models based on an atomic medium, one analytic, the other involving numerical simulation of a sequence of pump cycles. The predictions of both models are shown to agree. For regular pump excitation the intensity fluctuations of a laser well above threshold may be reduced to zero at the cavity resonance frequency if the ratio of the lifetimes of the upper and lower lasing levels is sufficiently large that spontaneous emission is suppressed. When the atomic lifetimes are comparable, spontaneous emission reduces the amount of noise reduction. For example, for equal atomic lifetimes regular pump excitation will result in a maximum noise reduction in the output field of one-half the shot-noise limit.
A Michelson interferometer with noise reduction to sub-shot noise levels is proposed and realized. Multiple measurements of a single signal beam are taken and the quantum property of light plays an essential role in the principle underlying this interferometry. The method makes use of the coherent state of light and requires only a simple modification to the standard Michelson interferometer. The surface fluctuation spectra of liquids are measured using this method down to a few orders of magnitude below the shot noise level. The spectrum derived from hydrodynamical considerations agrees well with the observed results for water. However, for oil, slight deviations are seen at high frequencies (≳1 \gtrsim1\,≳1MHz), perhaps indicating its more complex underlying physics. The measurement requires a relatively low light power and a short time, so that it has a wide range of applicability.