The standard method of quantum state tomography (QST) relies on the measurement of a set of noncommuting observables, realized in a series of independent experiments. Ancilla-assisted QST (AAQST) proposed by Nieuwenhuizen and co-workers [Phys. Rev. Lett. 92, 120402 (2004)] greatly reduces the number of independent measurements by exploiting an ancilla register in a known initial state. In suitable conditions AAQST allows mapping out density matrix of an input register in a single experiment. Here we describe methods for explicit construction of AAQST experiments in multiqubit registers. We also report nuclear magnetic resonance studies on AAQST of (i) a two-qubit input register using a one-qubit ancilla in an isotropic liquid-state system and (ii) a three-qubit input register using a two-qubit ancilla register in a partially oriented system. The experimental results confirm the effectiveness of AAQST in such multiqubit registers.
The standard method of quantum state tomography (QST) relies on the measurement of a set of noncommuting observables, realized in a series of independent experiments. Ancilla-assisted QST (AAQST) proposed by Nieuwenhuizen and co-workers [Phys. Rev. Lett. 92, 120402 (2004)] greatly reduces the number of independent measurements by exploiting an ancilla register in a known initial state. In suitable conditions AAQST allows mapping out density matrix of an input register in a single experiment. Here we describe methods for explicit construction of AAQST experiments in multiqubit registers. We also report nuclear magnetic resonance studies on AAQST of (i) a two-qubit input register using a one-qubit ancilla in an isotropic liquid-state system and (ii) a three-qubit input register using a two-qubit ancilla register in a partially oriented system. The experimental results confirm the effectiveness of AAQST in such multiqubit registers.
The standard procedure for quantum process tomography (QPT) requires a series of experiments. Each experiment involves initialization of the system to a particular basis state, applying the quantum process $\ensuremath{\varepsilon}$ on the system, and finally characterizing the output state by quantum state tomography (QST). The output states collected for a complete set of basis states enable us to calculate the $\ensuremath{\chi}$ matrix characterizing the process $\ensuremath{\varepsilon}$. The standard procedure for QST itself requires independent experiments, each involving measurement of a set of commuting observables. Thus QPT procedure demands a number of independent measurements and, moreover, this number increases rapidly with the size of the system. However, in ensemble systems, the total number of independent measurements can be greatly reduced with the availability of ancilla qubits. Ancilla-assisted process tomography (AAPT) has earlier been shown to require a single QST of system-ancilla space. Ancilla-assisted quantum state tomography (AAQST) has also been shown to perform QST in a single-scan measurement of an ensemble system. Here we combine AAPT with AAQST to realize a single-scan QPT (SSPT), a procedure to characterize a general quantum process in a single ensemble measurement. We demonstrate experimental SSPT by characterizing several single-qubit processes using a three-qubit NMR quantum register. Furthermore, using the SSPT procedure, we experimentally characterize the twirling process and compare the results with theory.
Quantum state tomography (QST) is a crucial tool for characterizing quantum states. However, performing full QST becomes impractical for reconstructing multiqubit density matrices since datasets and computational costs grow exponentially with qubit number. To bypass full QST, we introduce selective and efficient QST (SEEQST)—a method that enables efficient estimation of multiple selected elements of an arbitrary multiqubit density matrix. We show that any N -qubit density matrix can be partitioned into 2 N disjoint subsets, each containing 2 N elements. With SEEQST, any such subset can be accurately estimated from just two experiments with only single-qubit measurements. The complexity for estimating any subset remains constant regardless of Hilbert-space dimension, so, if desired, SEEQST can reconstruct the full density matrix, using 2 N + 1 − 1 experiments, where standard methods would use 3 N experiments. We provide a circuit decomposition for the SEEQST experiments, demonstrating that their maximum circuit depth scales logarithmically with N assuming all-to-all connectivity.
Quantum state tomography (QST) via local measurements on reduced density matrices (LQST) is a promising approach but becomes impractical for large systems. To tackle this challenge, we developed an efficient quantum state tomography method inspired by quantum overlapping tomography [Phys. Rev. Lett. 124, 100401 (2020)PRLTAO0031-900710.1103/PhysRevLett.124.100401], which utilizes parallel measurements (PQST). In contrast to LQST, PQST significantly reduces the number of measurements and offers more robustness against shot noise. Experimentally, we demonstrate the feasibility of PQST in a treelike superconducting qubit chip by designing high-efficiency circuits, preparing W states, ground states of Hamiltonians, and random states, and then reconstructing these density matrices using full quantum state tomography (FQST), LQST, and PQST. Our results show that PQST reduces measurement cost, achieving fidelities of 98.68% and 95.07% after measuring 75 and 99 observables for six-qubit and nine-qubit W states, respectively. Furthermore, the reconstruction of the largest density matrix of the 12-qubit W state is achieved with the similarity of 89.23% after just measuring 243 parallel observables, while 3^{12}=531 441 complete observables are needed for FQST. Consequently, PQST will be a useful tool for future tasks such as the reconstruction, characterization, benchmarking, and properties learning of states.
Quantum process tomography (QPT) is a fundamental task to characterize the dynamics of quantum systems. In contrast to standard QPT, ancilla-assisted process tomography (AAPT) framework introduces an extra ancilla system such that a single input state is needed. In this paper, we extend the two-stage solution, a method originally designed for standard QPT, to perform AAPT. Our algorithm hasO(MdA2dB2)computational complexity whereMis the type number of the measurement operators,dAis the dimension of the quantum system of interest, anddBis the dimension of the ancilla system. Then we establish an error upper bound and further discuss the optimal design on the input state in AAPT. A numerical example on a phase damping process demonstrates the effectiveness of the optimal design and illustrates the theoretical error analysis.
Quantum state tomography (QST) aims at reconstructing the state of a quantum system. However, in conventional QST, the number of measurements scales exponentially with the number of qubits. Here, we propose a QST protocol, in which the introduction of a threshold allows one to drastically reduce the number of measurements required for the reconstruction of the state density matrix without compromising the result accuracy. In addition, one can also use the same approach to reconstruct an approximated density matrix tailoring the number of measurements on the available resources. We experimentally demonstrate this protocol by performing the tomography of states up to 7 qubits. We show that our approach can lead to results in agreement with those obtained by QST even when the number of measurements is reduced by more than two orders of magnitude.
We perform quantum state tomography (QST) in a three-qubit system consisting of strongly coupled nuclear spins, known in the NMR literature as ABX systems. We find that the number of experiments necessary to perform QST in such systems can be reduced with respect to those containing three qubits weakly coupled, which reduces the experimental effort required for the complete density-matrix reconstruction. To test the procedure we implement the full protocol for quantum teleportation. The tomographic results demonstrate that the density matrix can be reconstructed with fewer operations and high fidelity.