Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1110.5623 · Applied Physics Letters

Bolometric response in graphene based superconducting tunnel junctions

Heli Vora, Piranavan Kumaravadivel, B. Nielsen, Xu Sheng Du

Published Apr 9, 2012• 74 citations
arXivHTMLPDF

Abstract

We fabricate graphene-TiOx-aluminum tunnel junctions and characterize their radio frequency response. Below the superconducting critical temperature of aluminum and when biased within the superconducting gap, the devices show enhanced dynamic resistance which increases with decreasing temperature. Application of radio frequency radiation affects the dynamic resistance through electronic heating. The relation between the electron temperature rise and the absorbed radiation power is measured, from which the bolometric parameters, including heat conductance, noise equivalent power, and responsivity, are characterized.

DOI
10.1063/1.3703117

Related papers

Graphene-Insulator-Superconductor junctions as thermoelectric bolometers

Leonardo Lucchesi, Federico Paolucci

We design a superconducting thermoelectric bolometer made of a Graphene-Insulator-Superconductor tunnel junction. Our detector has the advantage of being passive, as it directly transduces input power to a voltage without the need to modulate an external bias. We characterize the device via numerical simulation of the full nonlinear thermal dynamical model of the junction, considering heating of both sides of the junction. While estimating noise contributions, we found novel expressions due to the temperatures of both sides being different than the bath temperature. Numerical simulations show a Noise Equivalent Power ${\rm NEP}\sim 4\times 10^{-17}\,{\rm W}/\sqrt{\rm Hz}$ for an input power of $\sim10^{-16}\,{\rm W}$, a response time of $τ_{th}\sim 200\, {\rm ns}$ and an integration time to obtain a Signal-to-Noise Ratio ${\rm SNR}=1$ of $τ_{\rm SNR=1}\sim 100\,μ{\rm s}$ for an input power $\sim 10^{-13}\,{\rm W}$. Therefore, the device shows promise for large-array cosmological experiment applications, also considering its advantages for fabrication and heat budget.

cond-mat.mes-hallCross-listedarXiv:2512.14493•Physical Review Applied•Dec 17, 2025•1 citation

Capacitively Coupled Hot-Electron Nanobolometer with SIN Tunnel Junctions

L. S. Kuzmin, M. Yu. Fominsky, Alexei Kalabukhov +2 more

A capacitively coupled hot-electron nanobolometer (CC-HEB) is the simplest and most effective antenna-coupled bolometer. The bolometer consists of a small absorber connected to the superconducting antenna by tunnel junctions. The tunnel junctions used for high-frequency coupling also give perfect thermal isolation of hot electrons in the small volume of the absorber. The same tunnel junctions are used for temperature measurements and electron cooling. This bolometer does not suffer from the frequency limitations in the submillimeter range due to the high potential barrier of the tunnel junctions as does the microbolometer with Andreev mirrors (A-HEB), which is limited by the superconducting gap. Theoretical analyses show that the two-junction configuration more than doubles the sensitivity of the bolometer in current-biased mode compared to the single-junction configuration used for A-HEB. Another important advantage of CC-HEB is its simple two-layer technology for sample fabrication. Samples were fabricated with an absorber made of a bilayer of Cr and Al to match the impedance of the antenna. Electrodes were made of Al and tunnel junctions were formed over the Al oxide layer. The coupling capacitances of the tunnel junctions, C ≈ 20 fF, in combination with the inductance of the 10 μm absorber create a bandpass filter with a central frequency around 300 GHz. Bolometers are integrated with log-periodic and double-dipole planar antennas made of Au. The temperature response of bolometer structures was measured at temperatures down to 256 mK. In our experiment we observed dV/dT=1.3 mV/K, corresponding to responsivity S=0.2.109 V/W. For amplifier noise Vna=3nV/Hz1/2 at 1 kHz the estimated total noise equivalent power is NEP=1.5.10-17 W/Hz1/2. The intrinsic bolometer self noise Vnbol=0.5 nV/Hz1/2 corresponds to NEP=3.10-18 W/Hz1/2. For microwave evaluation of bolometer sensitivity we used a black body radiation source comprising a thin NiCr stimulator placed on the cold plate of cryostat in front of a CC-HEB attached to an extended hemisphere sapphire lens. This measurements were consistent with estimates based on the dc responsivity of the bolometer.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Feb 1, 2003•6 citations

Physics of proximity Josephson sensor

J. Voutilainen, Matti A. Laakso, Tero Tapio Heikkilä

We study the proximity Josephson sensor in both bolometric and calorimetric operation and optimize it for different temperature ranges between 25 mK and a few kelvin. We investigate how the radiation power is absorbed in the sensor and find that the irradiated system is typically in a weak nonequilibrium state. We show in detail how the proximity of the superconductors affects the device response: for example, via changes in electron-phonon coupling and out-of-equilibrium noise. In addition, we estimate the applicability of graphene as the absorber material.

arXiv:0906.5470•Journal of Applied Physics•Mar 15, 2010•17 citations

Terahertz direct-detection behavior of niobium nitride superconducting tunnel junctions above liquid helium temperature

Zheng Wang, Dong Liu, Shao-Liang Li +2 more

Niobium nitride (NbN) superconducting tunnel junctions (STJs) have an energy gap nearly double that of niobium STJs, making them potential sensitive detectors that operate at higher frequencies and temperatures. In this paper, we investigate the direct-detection behavior (i.e. the spectral response, current responsivity, noise characteristics, and noise equivalent power (NEP)) of a 500 GHz NbN STJ detector at temperatures from approximately 5 to 9 K. The detector shows an uncorrected NEP of 3.8 x 10(-13) W/root Hz around 5 K and 1.5 x 10(-12) W/root Hz at 9 K. Its performance can be further improved by adopting a cryogenically cooled readout circuit and fabricating the device with a wiring layer of higher critical-transition temperatures.

Superconductor Science and Technology•May 23, 2014•1 citation

Josephson junctions in superconducting coplanar DC bias cavities: Fundamental studies and applications

Felix E. Schmidt

This thesis investigates fundamental properties of Josephson junctions embedded in microwave circuits, and an application arising from this hybrid approach. We used the versatility of superconducting coplanar DC bias cavities to extract previously inaccessible information on phase coherent and subgap mechanisms of graphene Josephson junctions. Chapter 1 gives an introduction to the technology of Josephson field effect transistors, among which graphene junctions show promise for future improvements in quantum computation. Together with an overview of the Josephson effect in superconducting-semiconducting systems, we introduce the concept of coplanar DC bias cavities for probing Josephson junctions at gigahertz frequencies. In chapter 2, we describe the experimental methods developed for carrying out the subsequent measurements. We include details on fabrication, material properties and measurement setup. Results of graphene Josephson junctions embedded in DC bias microwave resonators are presented in chapters 3 and 4. By following the resonance frequency and losses of the circuit, we are able to extract the junctions’ Josephson inductance and subgap resistance. Studying the nonlinear power and bias current response reveals further information on the underlying loss mechanisms and current phase relation. We turn to an application of our hybrid bias cavity – Josephson junction devices to detect small, low-frequency currents in chapter 5. Our device is competitive with state-of-the-art techniques for microwave radiation detection and, with minor modifications, should be able to outperform existing technologies by orders of magnitude. Finally, we conclude the presented work in chapter 6 and provide an outlook on potential future research.

•Jul 28, 2020•0 citations

The Influence of LO Power Heating of the Tunnel Junction on the Performance of THz SIS Mixers

Alessandro Traini, Boon-Kok Tan, John Garrett +6 more

We describe the performance of a superconductor- insulator-superconductor (SIS) mixer operating in the frequency range of 780-950 GHz. Unlike most SIS mixers, the tunnel junction employs two different superconductors, a niobium nitride top and a niobium bottom electrode sandwiching an aluminum nitride barrier layer, fabricated on a niobium titanium nitride ground plane. The mixer was tested in a pulse tube cryostat, with all the optical components, in the signal path, mounted inside the vacuum environment to avoid attenuation of the RF signal as it propagates from the hot/cold loads to the mixer. With this setup, we have measured an RF-corrected noise temperature of ~220 K. In this article, we focus on investigating the influence of local oscillator (LO) power heating on the performance of the terahertz mixer. The increase in the junction's physical temperature can be observed experimentally by noting the suppression of the gap voltage in the pumped current-voltage (I-V ) curve as the LO pumping level is increased. Similar observation has already been reported, and attempts were made to estimate the effective temperature of the device using equations of heat transfer between the mixer chip layers. Here, we present an experimental method of quantifying this effect by recovering the effective temperature of the junction through comparing the pumped I-V curves at different pumping levels and fixed bath temperature, with the unpumped I-V curves obtained at varying bath temperatures. We also estimate, for the first time, the effect of heating on the noise temperature as a function of bath temperature and frequency. We show that for typical experimental parameters, the LO heating can increase the double-sideband receiver noise temperature by as much as 20%, and that in the frequency range of the measurements, the effective temperature of the junction at fixed LO power increases linearly with frequency at a rate of 0.5 K/100 GHz.

IEEE Transactions on Terahertz Science and Technology•Sep 30, 2020•5 citations
We fabricate graphene-TiOx-aluminum tunnel junctions and characterize their radio frequency response. Below the superconducting critical temperature of aluminum and when biased within the superconducting gap, the devices show enhanced dynamic resistance which increases with decreasing temperature. Application of radio frequency radiation affects the dynamic resistance through electronic heating. The relation between the electron temperature rise and the absorbed radiation power is measured, from which the bolometric parameters, including heat conductance, noise equivalent power, and responsivity, are characterized.
We design a superconducting thermoelectric bolometer made of a Graphene-Insulator-Superconductor tunnel junction. Our detector has the advantage of being passive, as it directly transduces input power to a voltage without the need to modulate an external bias. We characterize the device via numerical simulation of the full nonlinear thermal dynamical model of the junction, considering heating of both sides of the junction. While estimating noise contributions, we found novel expressions due to the temperatures of both sides being different than the bath temperature. Numerical simulations show a Noise Equivalent Power NEP∼4×10−17 W/Hz{\rm NEP}\sim 4\times 10^{-17}\,{\rm W}/\sqrt{\rm Hz}NEP∼4×10−17W/Hz​ for an input power of ∼10−16 W\sim10^{-16}\,{\rm W}∼10−16W, a response time of τth∼200 nsτ_{th}\sim 200\, {\rm ns}τth​∼200ns and an integration time to obtain a Signal-to-Noise Ratio SNR=1{\rm SNR}=1SNR=1 of τSNR=1∼100 μsτ_{\rm SNR=1}\sim 100\,μ{\rm s}τSNR=1​∼100μs for an input power ∼10−13 W\sim 10^{-13}\,{\rm W}∼10−13W. Therefore, the device shows promise for large-array cosmological experiment applications, also considering its advantages for fabrication and heat budget.
A capacitively coupled hot-electron nanobolometer (CC-HEB) is the simplest and most effective antenna-coupled bolometer. The bolometer consists of a small absorber connected to the superconducting antenna by tunnel junctions. The tunnel junctions used for high-frequency coupling also give perfect thermal isolation of hot electrons in the small volume of the absorber. The same tunnel junctions are used for temperature measurements and electron cooling. This bolometer does not suffer from the frequency limitations in the submillimeter range due to the high potential barrier of the tunnel junctions as does the microbolometer with Andreev mirrors (A-HEB), which is limited by the superconducting gap. Theoretical analyses show that the two-junction configuration more than doubles the sensitivity of the bolometer in current-biased mode compared to the single-junction configuration used for A-HEB. Another important advantage of CC-HEB is its simple two-layer technology for sample fabrication. Samples were fabricated with an absorber made of a bilayer of Cr and Al to match the impedance of the antenna. Electrodes were made of Al and tunnel junctions were formed over the Al oxide layer. The coupling capacitances of the tunnel junctions, C ≈ 20 fF, in combination with the inductance of the 10 μm absorber create a bandpass filter with a central frequency around 300 GHz. Bolometers are integrated with log-periodic and double-dipole planar antennas made of Au. The temperature response of bolometer structures was measured at temperatures down to 256 mK. In our experiment we observed dV/dT=1.3 mV/K, corresponding to responsivity S=0.2.109 V/W. For amplifier noise Vna=3nV/Hz1/2 at 1 kHz the estimated total noise equivalent power is NEP=1.5.10-17 W/Hz1/2. The intrinsic bolometer self noise Vnbol=0.5 nV/Hz1/2 corresponds to NEP=3.10-18 W/Hz1/2. For microwave evaluation of bolometer sensitivity we used a black body radiation source comprising a thin NiCr stimulator placed on the cold plate of cryostat in front of a CC-HEB attached to an extended hemisphere sapphire lens. This measurements were consistent with estimates based on the dc responsivity of the bolometer.
We study the proximity Josephson sensor in both bolometric and calorimetric operation and optimize it for different temperature ranges between 25 mK and a few kelvin. We investigate how the radiation power is absorbed in the sensor and find that the irradiated system is typically in a weak nonequilibrium state. We show in detail how the proximity of the superconductors affects the device response: for example, via changes in electron-phonon coupling and out-of-equilibrium noise. In addition, we estimate the applicability of graphene as the absorber material.
Niobium nitride (NbN) superconducting tunnel junctions (STJs) have an energy gap nearly double that of niobium STJs, making them potential sensitive detectors that operate at higher frequencies and temperatures. In this paper, we investigate the direct-detection behavior (i.e. the spectral response, current responsivity, noise characteristics, and noise equivalent power (NEP)) of a 500 GHz NbN STJ detector at temperatures from approximately 5 to 9 K. The detector shows an uncorrected NEP of 3.8 x 10(-13) W/root Hz around 5 K and 1.5 x 10(-12) W/root Hz at 9 K. Its performance can be further improved by adopting a cryogenically cooled readout circuit and fabricating the device with a wiring layer of higher critical-transition temperatures.
This thesis investigates fundamental properties of Josephson junctions embedded in microwave circuits, and an application arising from this hybrid approach. We used the versatility of superconducting coplanar DC bias cavities to extract previously inaccessible information on phase coherent and subgap mechanisms of graphene Josephson junctions. Chapter 1 gives an introduction to the technology of Josephson field effect transistors, among which graphene junctions show promise for future improvements in quantum computation. Together with an overview of the Josephson effect in superconducting-semiconducting systems, we introduce the concept of coplanar DC bias cavities for probing Josephson junctions at gigahertz frequencies. In chapter 2, we describe the experimental methods developed for carrying out the subsequent measurements. We include details on fabrication, material properties and measurement setup. Results of graphene Josephson junctions embedded in DC bias microwave resonators are presented in chapters 3 and 4. By following the resonance frequency and losses of the circuit, we are able to extract the junctions’ Josephson inductance and subgap resistance. Studying the nonlinear power and bias current response reveals further information on the underlying loss mechanisms and current phase relation. We turn to an application of our hybrid bias cavity – Josephson junction devices to detect small, low-frequency currents in chapter 5. Our device is competitive with state-of-the-art techniques for microwave radiation detection and, with minor modifications, should be able to outperform existing technologies by orders of magnitude. Finally, we conclude the presented work in chapter 6 and provide an outlook on potential future research.
We describe the performance of a superconductor- insulator-superconductor (SIS) mixer operating in the frequency range of 780-950 GHz. Unlike most SIS mixers, the tunnel junction employs two different superconductors, a niobium nitride top and a niobium bottom electrode sandwiching an aluminum nitride barrier layer, fabricated on a niobium titanium nitride ground plane. The mixer was tested in a pulse tube cryostat, with all the optical components, in the signal path, mounted inside the vacuum environment to avoid attenuation of the RF signal as it propagates from the hot/cold loads to the mixer. With this setup, we have measured an RF-corrected noise temperature of ~220 K. In this article, we focus on investigating the influence of local oscillator (LO) power heating on the performance of the terahertz mixer. The increase in the junction's physical temperature can be observed experimentally by noting the suppression of the gap voltage in the pumped current-voltage (I-V ) curve as the LO pumping level is increased. Similar observation has already been reported, and attempts were made to estimate the effective temperature of the device using equations of heat transfer between the mixer chip layers. Here, we present an experimental method of quantifying this effect by recovering the effective temperature of the junction through comparing the pumped I-V curves at different pumping levels and fixed bath temperature, with the unpumped I-V curves obtained at varying bath temperatures. We also estimate, for the first time, the effect of heating on the noise temperature as a function of bath temperature and frequency. We show that for typical experimental parameters, the LO heating can increase the double-sideband receiver noise temperature by as much as 20%, and that in the frequency range of the measurements, the effective temperature of the junction at fixed LO power increases linearly with frequency at a rate of 0.5 K/100 GHz.