Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1010.0954 · Applied Physics Letters

Microwave readout scheme for a Josephson phase qubit

Tobias Wirth, Jürgen Lisenfeld, Alexander V. Lukashenko, Alexey Vladimirovich Ustinov

Published Dec 27, 2010• 14 citations
arXivHTMLPDF

Abstract

We present experimental results on a microwave scheme for reading out a Josephson phase qubit. A capacitively shunted superconducting quantum interference device (SQUID) is used as a nonlinear resonator which is inductively coupled to the qubit. The flux state of the qubit is detected by measuring the amplitude and phase of a microwave pulse reflected from the SQUID resonator. By this low-dissipative method, the qubit state measurement time is reduced to 25 μs, which is much faster than the conventional readout performed by switching the SQUID to its nonzero dc voltage state. The readout scheme presented here allows for reading out multiple qubits using a single microwave line by employing frequency-division multiplexing.

DOI
10.1063/1.3533805

Related papers

Dispersive readout scheme for a Josephson phase qubit

Wirth, Tobias

We present experimental results on a dispersive scheme for reading out a Josephson phase qubit. A capacitively shunted dc-SQUID is used as a nonlinear resonator which is inductively coupled to the qubit. We detect the flux state of the qubit by measuring the amplitude and phase of a microwave pulse reflected from the SQUID resonator. By this low-dissipative method, we reduce the qubit state measurement time down to 25 microseconds, which is much faster than using the conventional readout performed by switching the SQUID to its non-zero dc voltage state. The demonstrated readout scheme allows for reading out multiple qubits using a single microwave line by employing frequency-division multiplexing.

Verhandlungen der Deutschen Physikalischen Gesellschaft•Jan 1, 2011•0 citations

Readout for phase qubits without Josephson junctions

Matthias Steffen, Shwetank Kumar, David Peter Divincenzo +4 more

We present a readout scheme for phase qubits which eliminates the read-out superconducting quantum interference device so that the entire qubit and measurement circuitry only require a single Josephson junction. Our scheme capacitively couples the phase qubit directly to a transmission line and detects its state after the measurement pulse by determining a frequency shift observable in the forward scattering parameter of the readout microwaves. This readout is extendable to multiple phase qubits coupled to a common readout line and can in principle be used for other flux biased qubits having two quasistable readout configurations.

arXiv:1001.1453•Applied Physics Letters•Mar 8, 2010•10 citations

Dispersive readout of a flux qubit at the single-photon level

Jedediah E Johnson, Emile Hoskinson, Chris Macklin +3 more

A superconducting flux qubit is inductively coupled to a superconducting quantum interference device (SQUID) magnetometer, capacitively shunted to form a 1.294-GHz resonator. The qubit-state-dependent resonator frequency is weakly probed with a microwave signal and detected with a microstrip SQUID amplifier. At a mean resonator occupation $\overline{n}=1.5$ photons, the readout visibility is increased by a factor of 4.5 over that using a cryogenic semiconductor amplifier. As $\overline{n}$ is increased from 0.008 to 0.1, no reduction in ${T}_{1}$ is observed, potentially enabling continuous monitoring of the qubit state.

arXiv:1109.2858•Physical Review B•Dec 15, 2011•20 citations

Demonstration of a multiplexer of dissipationless superconducting quantum interference devices

John A. B. Mates, Gene C Hilton, K. D. Irwin +2 more

We report on the development of a microwave superconducting quantum interference device (SQUID) multiplexer to read out arrays of low-temperature detectors. In this frequency-division multiplexer, superconducting resonators with different frequencies couple to a common transmission line and each resonator couples to a different dissipationless SQUID. We demonstrate multiple designs, with high-Q values (4100–18 000), noise as low as 0.17μΦ0∕Hz, and a naturally linear readout scheme based on flux modulation. This multiplexing approach is compatible with superconducting transition-edge sensors and magnetic calorimeters and is capable of multiplexing more than a thousand detectors in a single transmission line.

Applied Physics Letters•Jan 14, 2008•162 citations

Quantum state detection of a superconducting flux qubit using a dc-SQUID in the inductive mode

Adrian Lupaşcu, C. J. P. M. Harmans, Johan E. Mooij

We present a readout method for superconducting flux qubits. The qubit quantum flux state can be measured by determining the Josephson inductance of an inductively coupled dc superconducting quantum interference device (dc-SQUID). We determine the response function of the dc-SQUID and its back-action on the qubit during measurement. Due to driving, the qubit energy relaxation rate depends on the spectral density of the measurement circuit noise at sum and difference frequencies of the qubit Larmor frequency and SQUID driving frequency. The qubit dephasing rate is proportional to the spectral density of circuit noise at the SQUID driving frequency. These features of the back-action are qualitatively different from the case when the SQUID is used in the usual switching mode. For a particular type of readout circuit with feasible parameters we find that single shot readout of a superconducting flux qubit is possible.

arXiv:cond-mat/0410730•Physical Review B•May 13, 2005•27 citations

Phase coherent dynamics of a superconducting flux qubit with capacitive bias readout

Frank Deppe, M. Mariantoni, E. P. Menzel +7 more

We present a systematic study of the phase coherent dynamics of a superconducting three-Josephson-junction flux qubit. The qubit state is detected with the integrated-pulse method, which is a variant of the pulsed switching-dc-superconducting quantum interference device (SQUID) method. In this scheme, the dc SQUID bias current pulse is applied via a capacitor instead of a resistor, giving rise to a narrow bandpass instead of a pure low-pass filter configuration of the electromagnetic environment. Measuring one and the same qubit with both setups allows a direct comparison. With the capacitive method about four times faster switching pulses and an increased visibility are achieved. Furthermore, the deliberate engineering of the electromagnetic environment, which minimizes the noise due to the bias circuit, is facilitated. Right at the degeneracy point, the qubit coherence is limited by energy relaxation. We find two main noise contributions. White noise limits the energy relaxation and contributes to the dephasing far from the degeneracy point. $1∕f$ noise is the dominant source of dephasing in the direct vicinity of the optimal point. The influence of $1∕f$ noise is also supported by nonrandom beatings in the Ramsey and spin echo decay traces. Numeric simulations of a coupled qubit-oscillator system indicate that these beatings are due to the resonant interaction of the qubit with at least one pointlike fluctuator, coupled especially strongly to the qubit.

arXiv:0710.4455•Physical Review B•Dec 4, 2007•37 citations
We present experimental results on a microwave scheme for reading out a Josephson phase qubit. A capacitively shunted superconducting quantum interference device (SQUID) is used as a nonlinear resonator which is inductively coupled to the qubit. The flux state of the qubit is detected by measuring the amplitude and phase of a microwave pulse reflected from the SQUID resonator. By this low-dissipative method, the qubit state measurement time is reduced to 25 μs, which is much faster than the conventional readout performed by switching the SQUID to its nonzero dc voltage state. The readout scheme presented here allows for reading out multiple qubits using a single microwave line by employing frequency-division multiplexing.
We present experimental results on a dispersive scheme for reading out a Josephson phase qubit. A capacitively shunted dc-SQUID is used as a nonlinear resonator which is inductively coupled to the qubit. We detect the flux state of the qubit by measuring the amplitude and phase of a microwave pulse reflected from the SQUID resonator. By this low-dissipative method, we reduce the qubit state measurement time down to 25 microseconds, which is much faster than using the conventional readout performed by switching the SQUID to its non-zero dc voltage state. The demonstrated readout scheme allows for reading out multiple qubits using a single microwave line by employing frequency-division multiplexing.
We present a readout scheme for phase qubits which eliminates the read-out superconducting quantum interference device so that the entire qubit and measurement circuitry only require a single Josephson junction. Our scheme capacitively couples the phase qubit directly to a transmission line and detects its state after the measurement pulse by determining a frequency shift observable in the forward scattering parameter of the readout microwaves. This readout is extendable to multiple phase qubits coupled to a common readout line and can in principle be used for other flux biased qubits having two quasistable readout configurations.
A superconducting flux qubit is inductively coupled to a superconducting quantum interference device (SQUID) magnetometer, capacitively shunted to form a 1.294-GHz resonator. The qubit-state-dependent resonator frequency is weakly probed with a microwave signal and detected with a microstrip SQUID amplifier. At a mean resonator occupation n‾=1.5\overline{n}=1.5n=1.5 photons, the readout visibility is increased by a factor of 4.5 over that using a cryogenic semiconductor amplifier. As n‾\overline{n}n is increased from 0.008 to 0.1, no reduction in T1{T}_{1}T1​ is observed, potentially enabling continuous monitoring of the qubit state.
We report on the development of a microwave superconducting quantum interference device (SQUID) multiplexer to read out arrays of low-temperature detectors. In this frequency-division multiplexer, superconducting resonators with different frequencies couple to a common transmission line and each resonator couples to a different dissipationless SQUID. We demonstrate multiple designs, with high-Q values (4100–18 000), noise as low as 0.17μΦ0∕Hz, and a naturally linear readout scheme based on flux modulation. This multiplexing approach is compatible with superconducting transition-edge sensors and magnetic calorimeters and is capable of multiplexing more than a thousand detectors in a single transmission line.
We present a readout method for superconducting flux qubits. The qubit quantum flux state can be measured by determining the Josephson inductance of an inductively coupled dc superconducting quantum interference device (dc-SQUID). We determine the response function of the dc-SQUID and its back-action on the qubit during measurement. Due to driving, the qubit energy relaxation rate depends on the spectral density of the measurement circuit noise at sum and difference frequencies of the qubit Larmor frequency and SQUID driving frequency. The qubit dephasing rate is proportional to the spectral density of circuit noise at the SQUID driving frequency. These features of the back-action are qualitatively different from the case when the SQUID is used in the usual switching mode. For a particular type of readout circuit with feasible parameters we find that single shot readout of a superconducting flux qubit is possible.
We present a systematic study of the phase coherent dynamics of a superconducting three-Josephson-junction flux qubit. The qubit state is detected with the integrated-pulse method, which is a variant of the pulsed switching-dc-superconducting quantum interference device (SQUID) method. In this scheme, the dc SQUID bias current pulse is applied via a capacitor instead of a resistor, giving rise to a narrow bandpass instead of a pure low-pass filter configuration of the electromagnetic environment. Measuring one and the same qubit with both setups allows a direct comparison. With the capacitive method about four times faster switching pulses and an increased visibility are achieved. Furthermore, the deliberate engineering of the electromagnetic environment, which minimizes the noise due to the bias circuit, is facilitated. Right at the degeneracy point, the qubit coherence is limited by energy relaxation. We find two main noise contributions. White noise limits the energy relaxation and contributes to the dephasing far from the degeneracy point. 1∕f1∕f1∕f noise is the dominant source of dephasing in the direct vicinity of the optimal point. The influence of 1∕f1∕f1∕f noise is also supported by nonrandom beatings in the Ramsey and spin echo decay traces. Numeric simulations of a coupled qubit-oscillator system indicate that these beatings are due to the resonant interaction of the qubit with at least one pointlike fluctuator, coupled especially strongly to the qubit.