Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:0905.2897 · Optics Express

Single-laser, one beam, tetrahedral magneto-optical trap

Matthieu Vangeleyn, Paul F. Griffin, Erling Riis, Aidan S. Arnold

Published Jul 23, 2009• 79 citations
arXivHTMLPDF

Abstract

We have realized a 4-beam pyramidal magneto-optical trap ideally suited for future microfabrication. Three mirrors split and steer a single incoming beam into a tripod of reflected beams, allowing trapping in the four-beam overlap volume. We discuss the influence of mirror angle on cooling and trapping, finding optimum efficiency in a tetrahedral configuration. We demonstrate the technique using an ex-vacuo mirror system to illustrate the previously inaccessible supra-plane pyramid MOT configuration. Unlike standard pyramidal MOTs both the pyramid apex and its mirror angle are non-critical and our MOT offers improved molasses free from atomic shadows in the laser beams. The MOT scheme naturally extends to a 2-beam refractive version with high optical access. For quantum gas experiments, the mirror system could also be used for a stable 3D tetrahedral optical lattice.

DOI
10.1364/oe.17.013601

Related papers

Single-laser, one-beam, tetrahedral magneto-optical trap

Matthieu Vangeleyn, Paul F. Griffin, Ian A. McGregor +2 more

Shimizu et al. demonstrated an alternative of the usual six beam magneto-optical trap (MOT), using four independent beams in a tetrahedral configuration. This paper demonstrates a novel version of the four beam MOT using a triplet of mirrors to split and steer an incoming beam into three parts such that all four beams cross in the correct configuration. In the usual pyramid configuration, the MOT forms below the top surface of the pyramid and the absence of optical access strongly reduces any manipulation of the cold atomic cloud. In addition, a micro-fabricated tetrahedral configuration offers an ideal tool for a high phase stability optical lattice, with the benefit of fixed lattice geometry. In the demonstration setup, the triplet is positioned underneath the quartz vacuum chamber and its thickness had to be considered. Therefore, the angle of the mirrors is slightly more acute than in the ideal situation, resulting in 45Adeg beams, in order to form the MOT above the plate. Moreover, irect modulation of the diode current by a frequency corresponding to the alkali atom energy splitting in order to generate the repumping light is used. The setup was used to cool down87Rb atoms via the F = 2 and F' = 3 energy levels of the D2 transition line. With the traditional cooling/repump lasers, 1.3 x 106atoms were trapped. With a 10mW microwave source, we generated enough repump light into the laser to get 1.1 x 106atoms, that is 85% compared to the two laser setup.

Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC)•Jun 1, 2009•3 citations

Single-beam magneto-optical trap in back-to-back pyramidal and conical mirrors

Timothy H. Nguyen, Mariam Mchedlidze, Guanghui Su +3 more

A three-dimensional magneto-optical trap (MOT), acting as an efficient method for producing cold atoms from room-temperature atomic vapor, has been widely used to develop atomic sensors. Various compact MOTs using a single laser beam have been reported, simplifying apparatuses and leading to miniaturized devices. Here, we propose single-beam MOTs based on back-to-back pyramidal and conical mirrors. In such back-to-back mirrors, a MOT trapping volume is formed by an incident laser beam, a retroreflected beam, and multiple reflections from the mirror surfaces. We present the design of back-to-back mirrors and a series of compact MOT configurations, with the potential of increasing access to the MOT and simultaneously creating multiple MOTs. We demonstrate a MOT in a back-to-back conical mirror, loading \ensuremath{\sim}1 \ifmmode\times\else\texttimes\fi{} ${10}^{7}$ ${}^{87}\mathrm{Rb}$ atoms from background vapor and cooling the atoms to \ensuremath{\sim}7 \textmu{}K using polarization gradients. Single-beam MOTs based on back-to-back mirrors contribute to building compact and scalable cold-atom-based sensors.

arXiv:2507.07925•Physical Review Applied•Sep 29, 2025•5 citations

Laser cooling with a single laser beam and a planar diffractor

Matthieu Vangeleyn, Paul F. Griffin, Erling Riis +1 more

A planar triplet of diffraction gratings is used to transform a single laser beam into a four-beam tetrahedral magneto-optical trap. This "flat" pyramid diffractor geometry is ideal for future microfabrication. We demonstrate the technique by trapping and subsequently sub-Doppler cooling (87)Rb atoms to 30 μK.

arXiv:1006.4526•Optics Letters•Oct 11, 2010•73 citations

Single-beam atom trap in a pyramidal and conical hollow mirror

K. I. Lee, Jiho Kim, Heung‐Ryoul Noh +1 more

We present a novel and simple magneto-optical trap in pyramidal and in conical hollow mirrors, using a single beam. A diode laser having modulation sidebands at microwaves is used for cooling, trapping, and repumping of rubidium atoms in a vapor cell. When the laser is circularly polarized and sent into the hollow region, three pairs of counterpropagating beams are automatically produced therein that have the same polarization configuration as that of a conventional six-beam magneto-optical trap. The fluorescence by the trapped atoms and its mirror image are observed simultaneously. This system may be useful for atom-manipulation applications such as gravitational atom traps and atom waveguides.

Optics Letters•Aug 1, 1996•176 citations

High-flux source of laser-cooled rubidium atoms for quantum technology applications

Christopher J. Foot, Sean Ravenhall

We have used a pyramid magneto-optical trap (MOT) to create a compact source of cold rubidium atoms. The four dielectric-coated metal mirrors in vacuum are arranged in the form of a pyramid that creates the light field for a MOT from a single ingoing laser beam. The atoms are pushed out through a hole (aperture) in the apex of the pyramid, in a direction determined by the laser light, to give a flux of Rb-87 atoms greater than 2 × 10^10 per second with a mean velocity of 33 m/s (FWHM of 28 m/s) and a divergence of 58 mrad. The pyramid MOT has a unique mechanism for adjusting aperture size and it is highly suitable for portable quantum technology devices.

•Oct 5, 2020•0 citations

Generation of a cold atom beam from a pyramidal magneto-optical trap

J. L. Bliss, Kenneth G. Libbrecht, James M. Kohel +2 more

Summary form only given. A simple and robust design has been implemented based on the pyramidal trap geometry which allows use of single large diameter (/spl les/20 cm) laser beam to obtain large capture rates of atoms from the background vapor. The four 45/spl deg/ mirrors are truncated just before the apex of the pyramid, and the 1 cm/sup 2/ region at the center of the incident laser beam is retro-reflected by a /spl lambda//4 plate with a high-reflectance gold coating on the second surface. A small (1 mm diameter) hole in this retro-optic forms an extraction column for the atoms while maintaining a low conductance between the source region and an adjacent UHV chamber. The characterization of this large pyramidal low-velocity intense source (LVIS) is reported, including an investigation of scaling to very large (/spl ges/10 cm) high power (/spl sim/1 W) laser beams which should allow an improvement by a factor of 2-3 in beam flux over previous reports.

Quantum Electronics and Laser Science Conference•Jan 20, 2003•0 citations
We have realized a 4-beam pyramidal magneto-optical trap ideally suited for future microfabrication. Three mirrors split and steer a single incoming beam into a tripod of reflected beams, allowing trapping in the four-beam overlap volume. We discuss the influence of mirror angle on cooling and trapping, finding optimum efficiency in a tetrahedral configuration. We demonstrate the technique using an ex-vacuo mirror system to illustrate the previously inaccessible supra-plane pyramid MOT configuration. Unlike standard pyramidal MOTs both the pyramid apex and its mirror angle are non-critical and our MOT offers improved molasses free from atomic shadows in the laser beams. The MOT scheme naturally extends to a 2-beam refractive version with high optical access. For quantum gas experiments, the mirror system could also be used for a stable 3D tetrahedral optical lattice.
Shimizu et al. demonstrated an alternative of the usual six beam magneto-optical trap (MOT), using four independent beams in a tetrahedral configuration. This paper demonstrates a novel version of the four beam MOT using a triplet of mirrors to split and steer an incoming beam into three parts such that all four beams cross in the correct configuration. In the usual pyramid configuration, the MOT forms below the top surface of the pyramid and the absence of optical access strongly reduces any manipulation of the cold atomic cloud. In addition, a micro-fabricated tetrahedral configuration offers an ideal tool for a high phase stability optical lattice, with the benefit of fixed lattice geometry. In the demonstration setup, the triplet is positioned underneath the quartz vacuum chamber and its thickness had to be considered. Therefore, the angle of the mirrors is slightly more acute than in the ideal situation, resulting in 45Adeg beams, in order to form the MOT above the plate. Moreover, irect modulation of the diode current by a frequency corresponding to the alkali atom energy splitting in order to generate the repumping light is used. The setup was used to cool down87Rb atoms via the F = 2 and F' = 3 energy levels of the D2 transition line. With the traditional cooling/repump lasers, 1.3 x 106atoms were trapped. With a 10mW microwave source, we generated enough repump light into the laser to get 1.1 x 106atoms, that is 85% compared to the two laser setup.
A three-dimensional magneto-optical trap (MOT), acting as an efficient method for producing cold atoms from room-temperature atomic vapor, has been widely used to develop atomic sensors. Various compact MOTs using a single laser beam have been reported, simplifying apparatuses and leading to miniaturized devices. Here, we propose single-beam MOTs based on back-to-back pyramidal and conical mirrors. In such back-to-back mirrors, a MOT trapping volume is formed by an incident laser beam, a retroreflected beam, and multiple reflections from the mirror surfaces. We present the design of back-to-back mirrors and a series of compact MOT configurations, with the potential of increasing access to the MOT and simultaneously creating multiple MOTs. We demonstrate a MOT in a back-to-back conical mirror, loading \ensuremath{\sim}1 \ifmmode\times\else\texttimes\fi{} 107{10}^{7}107 87Rb{}^{87}\mathrm{Rb}87Rb atoms from background vapor and cooling the atoms to \ensuremath{\sim}7 \textmu{}K using polarization gradients. Single-beam MOTs based on back-to-back mirrors contribute to building compact and scalable cold-atom-based sensors.
We present a novel and simple magneto-optical trap in pyramidal and in conical hollow mirrors, using a single beam. A diode laser having modulation sidebands at microwaves is used for cooling, trapping, and repumping of rubidium atoms in a vapor cell. When the laser is circularly polarized and sent into the hollow region, three pairs of counterpropagating beams are automatically produced therein that have the same polarization configuration as that of a conventional six-beam magneto-optical trap. The fluorescence by the trapped atoms and its mirror image are observed simultaneously. This system may be useful for atom-manipulation applications such as gravitational atom traps and atom waveguides.
We have used a pyramid magneto-optical trap (MOT) to create a compact source of cold rubidium atoms. The four dielectric-coated metal mirrors in vacuum are arranged in the form of a pyramid that creates the light field for a MOT from a single ingoing laser beam. The atoms are pushed out through a hole (aperture) in the apex of the pyramid, in a direction determined by the laser light, to give a flux of Rb-87 atoms greater than 2 × 10^10 per second with a mean velocity of 33 m/s (FWHM of 28 m/s) and a divergence of 58 mrad. The pyramid MOT has a unique mechanism for adjusting aperture size and it is highly suitable for portable quantum technology devices.
Summary form only given. A simple and robust design has been implemented based on the pyramidal trap geometry which allows use of single large diameter (/spl les/20 cm) laser beam to obtain large capture rates of atoms from the background vapor. The four 45/spl deg/ mirrors are truncated just before the apex of the pyramid, and the 1 cm/sup 2/ region at the center of the incident laser beam is retro-reflected by a /spl lambda//4 plate with a high-reflectance gold coating on the second surface. A small (1 mm diameter) hole in this retro-optic forms an extraction column for the atoms while maintaining a low conductance between the source region and an adjacent UHV chamber. The characterization of this large pyramidal low-velocity intense source (LVIS) is reported, including an investigation of scaling to very large (/spl ges/10 cm) high power (/spl sim/1 W) laser beams which should allow an improvement by a factor of 2-3 in beam flux over previous reports.