Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:0809.3272 · Applied Physics Letters

Temperature dependence of critical current fluctuations in Nb/AlOx/Nb Josephson junctions

Shawn Pottorf, Vijay Patel, James E. Lukens

Published Jan 26, 2009• 15 citations
arXivHTMLPDF

Abstract

We measured the low frequency critical current noise in Nb/AlOx/Nb Josephson junctions. Unshunted junctions biased above the gap voltage and resistively shunted junctions biased near the critical current Ic have been measured. For both, the spectral density of δIc/Ic, Sic(f), is proportional to 1/f, scales inversely as the area A and is independent of Jc≡Ic/A over a factor of nearly 20 in Jc. For all devices measured at 4.2 K, Sic(1 Hz)=2.0±0.4×10−12/Hz when scaled to A=1 μm2. We find that, from 4.2 to 0.46 K, Sic(f) decreases linearly with temperature.

DOI
10.1063/1.3074446

Related papers

Flicker (1∕f) noise in the critical current of Josephson junctions at 0.09–4.2K

F. C. Wellstood, C. Urbina, John L. Clarke

We have measured the low-frequency noise in the critical current Ic of six dc superconducting quantum interference devices (SQUIDs) with resistively shunted Nb–NbOx–PbIn Josephson junctions in the temperature range T=0.09–4.2K. Each device is voltage biased, the applied flux is an integer number of flux quanta, and the current fluctuations are measured with a second dc SQUID. At low frequencies f, there is a component of the power spectrum of the critical current fluctuations given approximately by SIc(f)=CIc2T2∕Af, where A is the area of both junctions, and C≈(3.9±0.4)×10−23m2∕K2. For quantum bits based on Josephson junctions, the scaling of SIc(f) with T2 implies that the dephasing time limited by critical current l∕f noise should scale as 1∕T for temperatures down to at least 0.09K.

Applied Physics Letters•Nov 29, 2004•62 citations

Investigation of Current Noise in Underdamped Josephson Devices by Switching Current Measurements

C. Granata, Roberto Russo, Antonio Vettoliere +4 more

Experimental measurements on critical current noise in underdamped niobium based Josephson devices by a technique based on the switching current measurements is reported. By sweeping the junction with a current ramp we measure the critical current switching as a function of the time using the standard time of flight technique. In such a way it is possible to obtain the critical current fluctuations ΔIc=Ic(t)-<Ic(t)> and the relative standard deviations which corresponds to the root square of the current fluctuation power. Pointing at the white noise fluctuations (above few Hz) and taking into account the physical frequency of the device, it is possible to evaluate the power spectral density of the critical current. The analysis has involved high quality underdamped Josephson junctions having an area ranging from (4x4) μm2 to (40x40) μm2 in the temperature range from 4.2 K to few tenth of mK. These measurement provide very useful information about the intrinsic noise of Josephson devices involving SQUIDs and qubits.

Physics Procedia•Jan 1, 2012•2 citations

Measurement of Epitaxial NbN/AlN/NbN Tunnel Junctions With a Low Critical Current Density at Low Temperature

Wei Qiu, Hirotaka Terai, Z. Wang

Superconducting qubit circuits require high quality low critical current density Josephson tunnel junctions. We have developed high quality epitaxial NbN/AlN/NbN tunnel junctions with critical current density, Jc, ranging from as low as a few A/cm2to a few tens of kA/cm2. In this work, we measured current-voltage characteristics for junctions with a Jc~ 32 A/cm2in the temperature range from 17 mK to above 6.7 K. All the junctions are in good quality and have a high gap voltage (>; 5.5 mV). We found that the junctions' sub-gap resistances were temperature dependent above 2.5 K and saturated at temperatures below 2.5 K. A junction sub-gap leakage current Irof about 23 pA was measured. The voltage noise power spectral density for 3 junctions with different sizes has been measured at the base temperature of 17 mK with the junctions biased above the gap voltage. The spectral densities clearly show 1/fbehavior at low frequency and are proportional to the junction's linear dimension.

IEEE Transactions on Applied Superconductivity•Nov 10, 2010•5 citations

Harmonic current-phase relation in Nb–Al-based superconductor/insulator/normal conductor/insulator/superconductor-type Josephson junctions between 4.2 K and the critical temperature

Martin Götz, Vladimir V. Khanin, H. Schulze +6 more

For a study of the supercurrent–phase relationship, we have fabricated Nb/Al/AlOx/Al/AlOx/Al/Nb-based Josephson junctions of low critical current density. At 4.2 K, junctions of a nominal area of 10×10 μm2 showed a nonhysteretic dc current–voltage characteristic with a critical current of about 10 μA. Similar junctions were part of washer-type rf superconductor quantum interference devices. These samples were inductively coupled to high-quality tank circuits for measurements at 4.2 K or at higher temperatures up to values close to the critical temperature of niobium. In this range, the current–phase relation, as deduced from impedance measurements of the phase-biased junction, did not deviate significantly from the sinusoidal shape.

Applied Physics Letters•Aug 28, 2000•5 citations

Low frequency critical current noise and two level system defects in Josephson junctions

Christopher Nugroho

The critical current in a Josephson junction is known to exhibit a 1/f low frequency noise. Implemented as a superconducting qubit, this low frequency noise can lead to decoherence. While the 1/f noise has been known to arise from an ensemble of two level systems connected to the tunnel barrier, the precise microscopic nature of these TLSs remain a mystery. In this thesis we will present measurements of the 1/f low frequency noise in the critical current and tunneling resistance of Al-AlOx-Al Josephson junctions. Measurements in a wide range of resistively shunted and unshunted junctions confirm the equality of critical current and tunneling resistance noise. That is the critical current fluctuation corresponds to fluctuations of the tunneling resistance. In not too small Al-AlOx-Al junctions we have found that the fractional power spectral density scales linearly with temperature. We confirmed that the 1/f power spectrum is the result of a large number of two level systems modulating the tunneling resistance. At small junction areas and low temperatures, the number of thermally active TLSs is insufficient to integrate out a featureless 1/f spectral shape. By analyzing the spectral variance in small junction areas, we have been able to deduce the TLS defect density, n ~ 2.53 per micrometer squared per Kelvin spread in the TLS energy per factor e in the TLS lifetimes. This density is consistent with the density of tunneling TLSs found in glassy insulators, as well as the density deduced from coherent TLSs interacting at qubit frequencies. The deduced TLS density combined with the magnitude of the 1/f power spectral density in large area junctions, gives an average TLS effective area, A ~ 0.3 nanometer squared. In ultra small tunnel junctions, we have studied the time-domain dynamics of isolated TLSs. We have found a TLS whose dynamics is described by the quantum tunneling between the two localized wells, and a one-phonon absorption/emission switching rate. From the quantum limiting rate and the WKB approximation, we estimated that the TLS has a mass and tunneling distance product consistent with an atomic mass tunneling through crystal lattice distances. At higher temperatures TLSs have been found that obey a simple thermal activation dynamics. By analyzing the TLS response to an external electric field, we have deduced that the TLS electric dipole is in the order of, P ~ 1 electron-Angstrom, consistent with the TLS having the charge of one electron tunneling through a disorder potential of distances, d ~ 1 Angstrom.

•Jan 6, 2015•0 citations

Overdamped Josephson junctions with Nb/AlOx/Al/AlOx/Nb structure for integrated circuit application

Masaaki Maezawa, Akira Shoji

We present characteristics of overdamped Josephson junctions consisting of Nb/AlOx/Al/ AlOx/Nb structures. The junctions were fabricated using a well-developed Nb/AlOx/Nb-junction technology and showed well-defined Josephson characteristics at 4.2 K. The characteristic voltage Vc [the product of the critical current Ic and the effective normal resistance Rn(eff)] of junctions, which determines high-frequency performance of the junction, was in the range of 0.1–0.5 mV, and the critical current density Jc in the range of 102–104 A/cm2. Maximum-to-minimum variations in Ic over a wafer were ±4% for junctions with Vc=0.15 mV and ±13% for junctions with Vc=0.5 mV.

Applied Physics Letters•Jun 30, 1997•67 citations
We measured the low frequency critical current noise in Nb/AlOx/Nb Josephson junctions. Unshunted junctions biased above the gap voltage and resistively shunted junctions biased near the critical current Ic have been measured. For both, the spectral density of δIc/Ic, Sic(f), is proportional to 1/f, scales inversely as the area A and is independent of Jc≡Ic/A over a factor of nearly 20 in Jc. For all devices measured at 4.2 K, Sic(1 Hz)=2.0±0.4×10−12/Hz when scaled to A=1 μm2. We find that, from 4.2 to 0.46 K, Sic(f) decreases linearly with temperature.
We have measured the low-frequency noise in the critical current Ic of six dc superconducting quantum interference devices (SQUIDs) with resistively shunted Nb–NbOx–PbIn Josephson junctions in the temperature range T=0.09–4.2K. Each device is voltage biased, the applied flux is an integer number of flux quanta, and the current fluctuations are measured with a second dc SQUID. At low frequencies f, there is a component of the power spectrum of the critical current fluctuations given approximately by SIc(f)=CIc2T2∕Af, where A is the area of both junctions, and C≈(3.9±0.4)×10−23m2∕K2. For quantum bits based on Josephson junctions, the scaling of SIc(f) with T2 implies that the dephasing time limited by critical current l∕f noise should scale as 1∕T for temperatures down to at least 0.09K.
Experimental measurements on critical current noise in underdamped niobium based Josephson devices by a technique based on the switching current measurements is reported. By sweeping the junction with a current ramp we measure the critical current switching as a function of the time using the standard time of flight technique. In such a way it is possible to obtain the critical current fluctuations ΔIc=Ic(t)-<Ic(t)> and the relative standard deviations which corresponds to the root square of the current fluctuation power. Pointing at the white noise fluctuations (above few Hz) and taking into account the physical frequency of the device, it is possible to evaluate the power spectral density of the critical current. The analysis has involved high quality underdamped Josephson junctions having an area ranging from (4x4) μm2 to (40x40) μm2 in the temperature range from 4.2 K to few tenth of mK. These measurement provide very useful information about the intrinsic noise of Josephson devices involving SQUIDs and qubits.
Superconducting qubit circuits require high quality low critical current density Josephson tunnel junctions. We have developed high quality epitaxial NbN/AlN/NbN tunnel junctions with critical current density, Jc, ranging from as low as a few A/cm2to a few tens of kA/cm2. In this work, we measured current-voltage characteristics for junctions with a Jc~ 32 A/cm2in the temperature range from 17 mK to above 6.7 K. All the junctions are in good quality and have a high gap voltage (>; 5.5 mV). We found that the junctions' sub-gap resistances were temperature dependent above 2.5 K and saturated at temperatures below 2.5 K. A junction sub-gap leakage current Irof about 23 pA was measured. The voltage noise power spectral density for 3 junctions with different sizes has been measured at the base temperature of 17 mK with the junctions biased above the gap voltage. The spectral densities clearly show 1/fbehavior at low frequency and are proportional to the junction's linear dimension.
For a study of the supercurrent–phase relationship, we have fabricated Nb/Al/AlOx/Al/AlOx/Al/Nb-based Josephson junctions of low critical current density. At 4.2 K, junctions of a nominal area of 10×10 μm2 showed a nonhysteretic dc current–voltage characteristic with a critical current of about 10 μA. Similar junctions were part of washer-type rf superconductor quantum interference devices. These samples were inductively coupled to high-quality tank circuits for measurements at 4.2 K or at higher temperatures up to values close to the critical temperature of niobium. In this range, the current–phase relation, as deduced from impedance measurements of the phase-biased junction, did not deviate significantly from the sinusoidal shape.
The critical current in a Josephson junction is known to exhibit a 1/f low frequency noise. Implemented as a superconducting qubit, this low frequency noise can lead to decoherence. While the 1/f noise has been known to arise from an ensemble of two level systems connected to the tunnel barrier, the precise microscopic nature of these TLSs remain a mystery. In this thesis we will present measurements of the 1/f low frequency noise in the critical current and tunneling resistance of Al-AlOx-Al Josephson junctions. Measurements in a wide range of resistively shunted and unshunted junctions confirm the equality of critical current and tunneling resistance noise. That is the critical current fluctuation corresponds to fluctuations of the tunneling resistance. In not too small Al-AlOx-Al junctions we have found that the fractional power spectral density scales linearly with temperature. We confirmed that the 1/f power spectrum is the result of a large number of two level systems modulating the tunneling resistance. At small junction areas and low temperatures, the number of thermally active TLSs is insufficient to integrate out a featureless 1/f spectral shape. By analyzing the spectral variance in small junction areas, we have been able to deduce the TLS defect density, n ~ 2.53 per micrometer squared per Kelvin spread in the TLS energy per factor e in the TLS lifetimes. This density is consistent with the density of tunneling TLSs found in glassy insulators, as well as the density deduced from coherent TLSs interacting at qubit frequencies. The deduced TLS density combined with the magnitude of the 1/f power spectral density in large area junctions, gives an average TLS effective area, A ~ 0.3 nanometer squared. In ultra small tunnel junctions, we have studied the time-domain dynamics of isolated TLSs. We have found a TLS whose dynamics is described by the quantum tunneling between the two localized wells, and a one-phonon absorption/emission switching rate. From the quantum limiting rate and the WKB approximation, we estimated that the TLS has a mass and tunneling distance product consistent with an atomic mass tunneling through crystal lattice distances. At higher temperatures TLSs have been found that obey a simple thermal activation dynamics. By analyzing the TLS response to an external electric field, we have deduced that the TLS electric dipole is in the order of, P ~ 1 electron-Angstrom, consistent with the TLS having the charge of one electron tunneling through a disorder potential of distances, d ~ 1 Angstrom.
We present characteristics of overdamped Josephson junctions consisting of Nb/AlOx/Al/ AlOx/Nb structures. The junctions were fabricated using a well-developed Nb/AlOx/Nb-junction technology and showed well-defined Josephson characteristics at 4.2 K. The characteristic voltage Vc [the product of the critical current Ic and the effective normal resistance Rn(eff)] of junctions, which determines high-frequency performance of the junction, was in the range of 0.1–0.5 mV, and the critical current density Jc in the range of 102–104 A/cm2. Maximum-to-minimum variations in Ic over a wafer were ±4% for junctions with Vc=0.15 mV and ±13% for junctions with Vc=0.5 mV.