Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:0801.3351 · Applied Physics Letters

Multilayer atom chips for versatile atom micromanipulation

M. Trinker, S. Groth, Stefan Haslinger, Stephanie Manz, Thomas Betz, Stephan Schneider, I. Bar‐Joseph, Thorsten Schumm, Jörg Schmiedmayer

Published Jun 23, 2008• 51 citations
arXivHTMLPDF

Abstract

We employ a combination of optical and electron-beam lithography to create an atom chip combining submicron wire structures with larger conventional wires on a single substrate. The multilayer fabrication enables crossed wire configurations, greatly enhancing the flexibility in designing potentials for ultracold quantum gases and Bose–Einstein condensates. Large current densities of >6×107A∕cm2 and high voltages of up to 65V across 0.3μm gaps are supported by even the smallest wire structures. We experimentally demonstrate the flexibility of the next generation atom chip by producing Bose–Einstein condensates in magnetic traps created by a combination of wires involving all different fabrication methods and structure sizes.

DOI
10.1063/1.2945893

Related papers

Development, Fabrication and Characterisation of Atom Chips

S. Groth

Atom chips are robust and extremely powerful toolboxes for quantum optical experiments, since they make it possible to create exceedingly precise magnetic traps for neutral atoms with minimal field modulations. Accurate manipulation of trapped atoms is feasible with magnetic and electric fields created on the atom chip. Therefore atom chips with high quality surfaces and extremely well defined wires were build (roughness < 20nm). Furthermore new generations of atom chips were developed, like the multi-layer atom chip with contact-free wire crossings, the sub-micron structured atom chip and the semiconducting atom chip. Extensive characterisation measurements of atom chip wires demonstrated that the wires stand current densities of up to 10^7A/cm^2 for seconds and voltage differences of more than 500V over 10µm. From the different materials tested doped silicon with a thin silicon dioxide layer is the best qualified substrate for atom chip fabrication. The atom chips fabricated during this thesis have been used in many successful experiments, yielding numerous results. Moreover this thesis established the basics for many further experiments in atom physics and quantum optics and delivers complete instructions for the fabrication of all developed atom chips as well as an introduction to the experiments.

•Jan 1, 2006•4 citations

Foil-based atom chip for Bose–Einstein condensates

Chris J. Vale, Ben Upcroft, Matthew J. Davis +2 more

We describe a novel method of fabricating atom chips that are well suited to the production and manipulation of atomic Bose–Einstein condensates. Our chip was created using a silver foil and simple micro-cutting techniques without the need for photolithography. It can sustain larger currents than conventional chips, and is compatible with the patterning of complex trapping potentials. A near pure Bose–Einstein condensate of 4 × 10 4 87 Rb atoms has been created in a magnetic microtrap formed by currents through wires on the chip. We have observed the fragmentation of atom clouds in close proximity to the silver conductors. The fragmentation has different characteristic features to those seen with copper conductors.

arXiv:cond-mat/0406015•Journal of Physics B Atomic Molecular and Optical Physics•Jul 9, 2004•22 citations

Fabrication and process characterization of atom transistor chips

Ho‐Chiao Chuang, Evan A. Salim, Vladan Vuletić +2 more

This paper describes the design and fabrication of an atom chip for atom tunneling experiments. A fabrication process was developed that uses a combination of UV-optical and Electron-Beam lithography to pattern micrometer and nanometer scale copper wires on a single chip. The minimum wire width fabricated in this work is 200 nm. The wires can carry current densities of more than 7.5times107A/cm2. The electrical current tests establish the feasibility of realizing chip-based atom tunneling experiments.

International Conference on Solid-State Sensors, Actuators and Microsystems•Jun 1, 2009•0 citations

Atom chips: Fabrication and thermal properties

S. Groth, P. Krüger, S. Wildermuth +5 more

Neutral atoms can be trapped and manipulated with surface mounted microscopic current carrying and charged structures. We present a lithographic fabrication process for such atom chips based on evaporated metal films. The size limit of this process is below 1 μm. At room temperature, thin wires can carry current densities of more than 107A∕cm2 and voltages of more than 500 V. Extensive test measurements for different substrates and metal thicknesses (up to 5 μm) are compared to models for the heating characteristics of the microscopic wires. Among the materials tested, we find that Si is the best suited substrate for atom chips.

arXiv:cond-mat/0404141•Applied Physics Letters•Oct 4, 2004•107 citations

Microelectromagnets for trapping and manipulating ultracold atomic quantum gases

József Fortágh, Herwig Ott, G. Schlotterbeck +3 more

We describe the production and characterization of microelectromagnets made for trapping and manipulating atomic ensembles. The devices consist of seven fabricated parallel copper conductors 3 μm thick, 25 mm long, with widths ranging from 3 to 30 μm, and are produced by electroplating a sapphire substrate. Maximum current densities in the wires up to 6.5×106 A cm−2 are achieved in continuous mode operation. The device operates successfully at a base pressure of 10−11 mbar. The microstructures permit the realization of a variety of magnetic field configurations and, hence, provide enormous flexibility for controlling the motion and the shape of Bose–Einstein condensates.

arXiv:cond-mat/0205586•Applied Physics Letters•Aug 5, 2002•23 citations

Atom Chip Fabrication

R. Folman, Philipp Treutlein, Jörg Schmiedmayer

This chapter overviews atom chip fabrication by discussing the challenges to be faced when starting to conceive and fabricate chips for the manipulation of atoms. It describes the various ingredients and the corresponding fabrication methods. The chapter focuses not only on the currently most active and successful areas - current carrying wires and integrated photonics, but also focuses on more visionary approaches, examples being superconducting chips or the manipulation of atoms with real nanostructures such as carbon nanotubes. It discusses the material engineering and fabrication of atom chips for the manipulation of neutral atoms, but the same concept of robustness and versatility through miniaturization and integration can also be applied to manipulate molecules, ions, or trapped electrons. Metallic wires, electrodes, or permanent magnets are the most commonly used structures on an atom chip. In lithography, a pattern is transferred into a layer of resist on the chip surface. Controlled Vocabulary Terms electron beam lithography; metallic thin films; microfabrication

Wiley eBooks•Feb 9, 2011•10 citations
We employ a combination of optical and electron-beam lithography to create an atom chip combining submicron wire structures with larger conventional wires on a single substrate. The multilayer fabrication enables crossed wire configurations, greatly enhancing the flexibility in designing potentials for ultracold quantum gases and Bose–Einstein condensates. Large current densities of >6×107A∕cm2 and high voltages of up to 65V across 0.3μm gaps are supported by even the smallest wire structures. We experimentally demonstrate the flexibility of the next generation atom chip by producing Bose–Einstein condensates in magnetic traps created by a combination of wires involving all different fabrication methods and structure sizes.
Atom chips are robust and extremely powerful toolboxes for quantum optical experiments, since they make it possible to create exceedingly precise magnetic traps for neutral atoms with minimal field modulations. Accurate manipulation of trapped atoms is feasible with magnetic and electric fields created on the atom chip. Therefore atom chips with high quality surfaces and extremely well defined wires were build (roughness < 20nm). Furthermore new generations of atom chips were developed, like the multi-layer atom chip with contact-free wire crossings, the sub-micron structured atom chip and the semiconducting atom chip. Extensive characterisation measurements of atom chip wires demonstrated that the wires stand current densities of up to 10^7A/cm^2 for seconds and voltage differences of more than 500V over 10µm. From the different materials tested doped silicon with a thin silicon dioxide layer is the best qualified substrate for atom chip fabrication. The atom chips fabricated during this thesis have been used in many successful experiments, yielding numerous results. Moreover this thesis established the basics for many further experiments in atom physics and quantum optics and delivers complete instructions for the fabrication of all developed atom chips as well as an introduction to the experiments.
We describe a novel method of fabricating atom chips that are well suited to the production and manipulation of atomic Bose–Einstein condensates. Our chip was created using a silver foil and simple micro-cutting techniques without the need for photolithography. It can sustain larger currents than conventional chips, and is compatible with the patterning of complex trapping potentials. A near pure Bose–Einstein condensate of 4 × 10 4 87 Rb atoms has been created in a magnetic microtrap formed by currents through wires on the chip. We have observed the fragmentation of atom clouds in close proximity to the silver conductors. The fragmentation has different characteristic features to those seen with copper conductors.
This paper describes the design and fabrication of an atom chip for atom tunneling experiments. A fabrication process was developed that uses a combination of UV-optical and Electron-Beam lithography to pattern micrometer and nanometer scale copper wires on a single chip. The minimum wire width fabricated in this work is 200 nm. The wires can carry current densities of more than 7.5times107A/cm2. The electrical current tests establish the feasibility of realizing chip-based atom tunneling experiments.
Neutral atoms can be trapped and manipulated with surface mounted microscopic current carrying and charged structures. We present a lithographic fabrication process for such atom chips based on evaporated metal films. The size limit of this process is below 1 μm. At room temperature, thin wires can carry current densities of more than 107A∕cm2 and voltages of more than 500 V. Extensive test measurements for different substrates and metal thicknesses (up to 5 μm) are compared to models for the heating characteristics of the microscopic wires. Among the materials tested, we find that Si is the best suited substrate for atom chips.
We describe the production and characterization of microelectromagnets made for trapping and manipulating atomic ensembles. The devices consist of seven fabricated parallel copper conductors 3 μm thick, 25 mm long, with widths ranging from 3 to 30 μm, and are produced by electroplating a sapphire substrate. Maximum current densities in the wires up to 6.5×106 A cm−2 are achieved in continuous mode operation. The device operates successfully at a base pressure of 10−11 mbar. The microstructures permit the realization of a variety of magnetic field configurations and, hence, provide enormous flexibility for controlling the motion and the shape of Bose–Einstein condensates.
This chapter overviews atom chip fabrication by discussing the challenges to be faced when starting to conceive and fabricate chips for the manipulation of atoms. It describes the various ingredients and the corresponding fabrication methods. The chapter focuses not only on the currently most active and successful areas - current carrying wires and integrated photonics, but also focuses on more visionary approaches, examples being superconducting chips or the manipulation of atoms with real nanostructures such as carbon nanotubes. It discusses the material engineering and fabrication of atom chips for the manipulation of neutral atoms, but the same concept of robustness and versatility through miniaturization and integration can also be applied to manipulate molecules, ions, or trapped electrons. Metallic wires, electrodes, or permanent magnets are the most commonly used structures on an atom chip. In lithography, a pattern is transferred into a layer of resist on the chip surface. Controlled Vocabulary Terms electron beam lithography; metallic thin films; microfabrication