Using a new general approach to limits in optical structures that counts orthogonal waves generated by scattering, we derive an upper limit to the number of bits of delay possible in one-dimensional slow light structures that are based on linear optical response to the signal field. The limit is essentially the product of the length of the structure in wavelengths and the largest relative change in dielectric constant anywhere in the structure at any frequency of interest. It holds for refractive index, absorption, or gain variations with arbitrary spectral or spatial form. It is otherwise completely independent of the details of the structure's design, and does not rely on concepts of group velocity or group delay.
Using a new general approach to limits in optical structures that counts orthogonal waves generated by scattering, we derive an upper limit to the number of bits of delay possible in one-dimensional slow light structures that are based on linear optical response to the signal field. The limit is essentially the product of the length of the structure in wavelengths and the largest relative change in dielectric constant anywhere in the structure at any frequency of interest. It holds for refractive index, absorption, or gain variations with arbitrary spectral or spatial form. It is otherwise completely independent of the details of the structure's design, and does not rely on concepts of group velocity or group delay.
One of the key issues when dealing with slow light is the inevitable effect of dispersion, the result of which is to broaden a pulse upon propagation. Moreover, the dispersion tends to increase when the group velocity, the speed at which the pulse propagates, decreases. To see this, we note that if we write the group velocity vg ≡ c/ng, where ng is the group index, then we find that ng = n+ωdn/dω. Since for the materials we are interested in, the refractive index does not vary strongly in magnitude, and slow light is obtained when the derivative dn/dω is large and positive. However, as the variations in the magnitude of n itself are limited, the large derivative can only be maintained over a narrow bandwidth ∝ (dn/dω)−1. Therefore, a large delay implies a narrow bandwidth, and hence a limited pulse width. Here we discuss how to avoid this limit by using nonlinear effects in the form of gap solitons. Though this argument is quite simple, it can be made rigorous using the Kramers-Kronig relations. In this way it can be shown that the achievable delay in a linear, two-port device is subject to a limitation of the product of the delay and the bandwidth (Lenz et al., 2001).
This paper presents an analysis of optical buffers based on slow-light optical delay lines. The focus of this paper is on slow-light delay lines in which the group velocity is reduced using linear processes, including electromagnetically induced transparency (EIT), population oscillations (POs), and microresonator-based photonic-crystal (PC) filters. We also consider slow-light delay lines in which the group velocity is reduced by an adiabatic process of bandwidth compression. A framework is developed for comparing these techniques and identifying fundamental physical limitations of linear slow-light technologies. It is shown that slow-light delay lines have limited capacity and delay-bandwidth product. In principle, the group velocity in slow-light delay lines can be made to approach zero. But very slow group velocity always comes at the cost of very low bandwidth or throughput. In many applications, miniaturization of the delay line is an important consideration. For all delay-line buffers, the minimum physical size of the buffer for a given number of buffered data bits is ultimately limited by the physical size of each stored bit. We show that in slow-light optical buffers, the minimum achievable size of 1 b is approximately equal to the wavelength of light in the buffer. We also compare the capabilities and limitations of a range of delay-line buffers, investigate the impact of waveguide losses on the buffer capacity, and look at the applicability of slow-light delay lines in a number of applications.
All resonant systems throughout science and engineering, independent of their physical implementation have a bandwidth that is inversely related to the decay time. A similar relation exists in all slow-light systems, where the group index (and therefore the delay for a given footprint) is inversely related to the bandwidth. Therefore, resonant or slow-light systems can either store a broad signal for a short time, or a narrow signal for a long time, but cannot achieve large delay for broad bandwidth signals.Here we discuss our recent work on non-reciprocal optical systems that are not constrained by the delay-bandwidth limit. We show that large, broadband optical delay is not a pipe dream and is achievable with current optical technology. We discuss the underlying physics of delay and bandwidth in non-reciprocal optical systems and present an experimental implementation, based on a figure-9 cavity. We demonstrate a delay-bandwidth product 30 times above the seemingly fundamental time-bandwidth limit of traditional systems. Furthermore, we show that the optical pulse can be released after an arbitrary number of round trips, providing the control and tunability lacking from conventional spiral waveguide or fibre loop delay lines.
Ultra-slow light and complete transmission properties in one-dimensional Cantor photonic crystals are presented. In contrast to traditional dielectric photonic crystals, the proposed structure has large group delay, slower group velocity, and a high quality factor within the same layers and materials. This study shows that larger than 1 μs group delay and slower than 1 m/s group velocity are achieved in the fifth-order Cantor photonic crystal with 52.75 μm length. This ultra-slow-light structure is very promising for application in advanced slow-light devices. A high quality factor of 109 and multiband filters with complete transmission can also be obtained by using this approach.
The group velocity at which light pulses propagate through a dispersive material system is very different from the vacuum speed of light c, One refers to light as being "slow" for v g << c (Boyd & Gauthier, 2009) or "fast" for v g > c or v g <0 (Stenner et al, 2003 ).For v g <0, the pulse envelope appears to travel backward in the material (Gehring et al, 2006), and hence it is sometimes referred to as "backward light."The subject of slow light has caused keen interest in the past decade or more, and it is possible to control the group velocity of light pulses in the dispersive materials.Interest in slow and fast light dates back to the early days of the 20th century.Sommerfeld and Brillouin (Sommerfeld & Brillouin, 1960) were intrigued by the fact that theory predicts that v g can exceed c, which leads to apparent inconsistencies with Einstein's special theory of relativity.Experimental investigations of extreme propagation velocities were performed soon after the invention of the laser (Faxvog and et al, 1970).In 1999, Harris's group research work greatly stimulated researchers' interests, which showed that light could be slowed down to 17m/s.The result was obtained in ultra cold atom clouds with the use of electromagnetically induced transparency (EIT), which induces transparency in a material while allowing it to retain strong linear and nonlinear optical properties (Hau et al, 1999).Slow light can also be obtained through the use of the optical response of hot atomic vapors (Philips et al, 2001).These early research works require hard conditions and the slow light cannot operate in room temperature.Recently, researchers found ways to realize slow light operating in room temperature and solid-state materials, which are more suited for many practical applications, namely slow light via stimulated Brillouin scattering(SBS), slow light via coherent population oscillations (CPO), tunable time delays based on group velocity dispersion or conversion/ dispersion(C/D), slow light in fiber Bragg gratings and so on.In this chapter, we describe some of the physical mechanisms that can be used to induce slow and fast light effects in room-temperature solids (Bigelow et al, 2003) and some of the exotic propagation effects that can thereby be observed.We also survey some applications of slow and fast light within the fields of quantum electronics and photonics. Fundamentals of slow and fast lightSlow and fast light refer to the group velocity of a light wave.The group velocity is the velocity most closely related to the velocity at which the peak of a light pulse moves through an optical dispersive material (Milonni, 2005), and is given by the standard result www.intechopen.comRecent Progress in Optical Fiber Research 82where n is the refractive (phase) index and ω is the angular frequency of the carrier wave of the light field.One refers to light as being slow light for v g << c, fast light for for v g > c, and backwards light for v g <0 or v g is negative.Extreme values of the group velocity invariably rely on the dominance of the second contribution to the group index of Equation ( 1).This contribution of course results from the frequency dependence of the refractive index, and for this reason extreme values of the group velocity are usually associated with the resonant or near-resonant response of material systems.According to this theory, slow light is expected in the wings of an absorption line and fast light is expected near line center, and the spatial dispersion, that is, the non-locality in space of the medium response, is another mechanism that can lead to slow light, as has been predicted (Kocharovskaya et al,2001) and observed (Strekalov et al, 2001).We catalogue the main methods to realize slow light in room temperature solid, namely slow light via stimulated Brillouin scattering(SBS), slow light via coherent population oscillations (CPO), tunable time delays based on group velocity dispersion or conversion/ dispersion(C/D), slow light in fiber Bragg gratings and so on.We will describe CPO and SBS slow light in more details.
Frontiers in Guided Wave Optics and Optoelectronics 84 absorption is much too high to render the group effect useful.An exciting breakthrough happened in the early nineties when it was shown that group velocities of few tens of meters per second were possible with nonlinear resonance interactions (Hau et al., 1999).Two important features of nonlinear resonances make this possible: substantially reduced absorption, or even amplification, of radiation at a resonance, and sharpness of such resonances; the sharper a resonance, the higher dn/dω and so the stronger the enhancement of group index, and hence the greater the pulse is delayed.Widely ranging applications for slow light have been proposed, of which those for telecommunication systems and devices (optical delay lines, optical buffers, optical equalizers and signal processors) are currently of most interest (Gauthier, 2005).The essential demand of such devices is compatibility with existing telecommunication systems, that is they must be of wide enough bandwidth (≥10 GHz) and able to be integrated seamlessly into such systems.Of the various nonlinear resonance mechanisms and media, which allow sufficiently long induced delays, stimulated Brillouin and Raman scattering (SBS and SRS) in optical fiber are deemed to be among the best candidates.Currently SBS is the most actively investigated and many experimental and theoretical papers on pulse delaying via SBS in optical fiber have been published in the last few years, see the review paper (Thevenaz, 2008) and references therein.In this process the pulse to be delayed is a frequency down-shifted (Stokes) pulse.This is transmitted through an optical fiber through which continuous wave (CW) pump radiation is sent in the opposite direction to prime the delay process.It is supposed that the Stokes pulse is amplified by parametric coupling with the pump wave and a material (acoustic) wave in the medium (Kroll, 1965), and the amplification is characterised by a resonant-type gain profile.The dispersion of refractive index associated with this profile (which is similar to that in Fig. 1) can then be used to increase the group index for optical pulses at the Stokes frequency (Zeldovich, 1972).Along with obvious device compatibility, there are several other advantages of the SL via SBS approach for optical communications systems: slow-light resonance can be created at any wavelength by changing the pump wavelength; use of optical fibre allows for long interaction lengths and thus low powers for the pump radiation, the process runs at room temperature, it uses off the shelf telecom equipment, and SBS works in the entire transparency range of fibers and in all types of fiber.Currently a main obstacle to applications of this approach is the narrow SBS gain spectral bandwidth, (Thevenaz, 2008), which is typically ≈ 120-200 MHz in silica fiber in the spectral range of telecom optical radiation (~1.3-1.6 μm) (Agrawal, 2006).This chapter reviews our ongoing work on the physical mechanisms that give rise to pulse delay in SBS.In section 2 the theoretical background of the SBS phenomenon is given and the main working equations describing this nonlinear interaction are presented.In section 3 ways by which the SBS spectral bandwidth may be increased are addressed.Waveguide induced spectral broadening of SBS in optical fibre is considered as a means of increasing the bandwidth to the multi-GHz range.An alternative way widely discussed in the literature, (Thevenaz, 2008), is based on spectral broadening of the pump radiation.However it is shown through analytic analysis of the SBS equations converted to the frequency domain that pump radiation broadening by any reasonable amount has only a negligible effect on increasing the SBS bandwidth.Importantly in this section we show that, irrespective of the nature of the broadening considered, the SBS gain bandwidth remains www.intechopen.